ContractBeam
The Registry

Browse opportunities

76 opportunities · showing 21–40

Active only
For youRelevanceClosing soonNewestHighest value
“engineering OR technical”✕Agency: DEPT OF DEFENSE✕clear all
ContractTotal Small Business Set-Aside (FAR 19.5)1 day left

MEARNG Camp Chamberlain Cell Repeater

Amendment 0001 - The Government has issued an official responsed to questions raised by interested parties - 7-9-2026 The Maine Army National Guard requires a Contractor to furnish, install, test, and commission a turnkey, multi-carrier in-building cellular enhancement/repeater solution at Joint Force Headquarters, Camp Chamberlain, located in Augusta, Maine. The current system has failed, resulting in inadequate cellular coverage. The objective of this acquisition is to procure a fully functional, Trade Agreements Act (TAA) compliant Distributed Antenna System (DAS) headend/controller solution that integrates with the building's existing passive infrastructure. The final solution must resolve current service failures and provide robust, reliable 5G and LTE cellular coverage for Verizon, AT&T, and T-Mobile across an area of approximately 100,000 square feet. This is a Firm-Fixed-Price (FFP) requirement. Award will be made based on Lowest Price Technically Acceptable (LPTA) source selection procedures. Key Requirements (See attached PWS for full details): Conduct a post-award site survey and submit a detailed system design. Furnish and install a complete, TAA-compliant headend/controller solution. The contractor is responsible for obtaining all necessary carrier rebroadcast agreements/consents (Verizon, AT&T, T-Mobile) and FCC registrations prior to system activation. Perform post-installation grid testing to validate the system meets approved commercial carrier standards. Provide a one (1) year system warranty. Pre-Proposal Site Visit: Offerors or quoters are urged and expected to inspect the site where services are to beperformed and to satisfy themselves regarding all general and local conditions that may affect the cost of contract performance, to the extent that the information is reasonably obtainable. In no event shall failure to inspect the site constitute grounds for a claim after contract award. The site visill will not be available at any other times prior to the bid due date. Due to secruity conditions, all interested parties must register to attend this site-visit. To enter the base, individuals must have a picture identificaiton card when entering the front gate. Email the following information for all attendees no later than Friday, 10JUL2026 by sending an email to the Contract Specialist, Tom Ryan at thomas.j.ryan36.civ@army.mil. Date of Site Visit: 15 July 2026 Time of Site Visit: 10:00 AM (EDT) Location: Camp Chamberlain, 23 Blue Star Ave, Augusta, Maine 04333 Point of Contact: Thomas J. Ryan (thomas.j.ryan36.civ@army.mil) Submission Instructions: All quotes must be submitted via email to the Contract Specialist, Thomas J. Ryan, at thomas.j.ryan36.civ@army.mil and the Contracting Officer Darlene Howes, at darlene.r.howes.civ@army.mil. Quotes must include a completed SF 1449 and a separate Technical Proposal responding to the evaluation criteria outlined in the FAR 52.212-1 and 52.212-2 Addenda.

AgencyDEPT OF DEFENSE
NAICS517112
PlaceAugusta, ME
SAM.gov· Posted Jul 9, 2026#W912JD26QA016
Contract1 day left

81--SHIPPING AND STORAG

CONTACT INFORMATION|4|APAC.41|YGR|445-737-3493|makayla.hauser@dla.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT|8|x|||||||| STOP-WORK ORDER (AUG 1989)|1|| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (combo).||TBD|SPRPA1|TBD|TBD|See schedule|TBD||||||||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|| MANDATORY USE OF WORKFLOW PRO (WFP) MOD ASSIST MODULE|1|robyn.grinarml@dla.mil| VALUE ENGINEERING (JUN 2020)|3|||| INTEGRITY OF UNIT PRICES (NOV 2021)|1|| EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (DEV 2026-O0040)(FEB 2026)|4||||| TRANSPORTATION OF SUPPLIES BY SEA (OCT 2024)|2||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11|||||||||||| LIMITATION OF LIABILITY--HIGH-VALUE ITEMS (FEB 1997)|1|| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (DEV 2026-O0037)(FEB 2026)|1|| SECURITY PROHIBITIONS AND EXCLUSIONS (CLASS DEVIATION 2026-O0025)(FEB 2026)|7|||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5|||||| BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0043)(FEB 2026))|13|||||||||||||| ROYALTY INFORMATION (APR 1984)|1|| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x| ONLY ONE OFFER (DEVIATION 2026-O0048)(MAR 2026)|1|| THIS ITEM REQUIRES ENGINEERING SOURCE APPROVAL BY THE DESIGN ACTIVITY IN ORDER TO MAINTAIN THE QUALITY OF THE PART. IF YOU HAVE NOT MANUFACTURED THIS ITEM BEFORE FOR DLA WEAPONS SUPPORT PHILADELPHIA AND WANT TO BECOME AN APPROVED SOURCE OF SUPPLY, PLEASE CONTACT THE BUYER BY EMAIL TO INQUIRE ABOUT SOURCE APPROVAL REQUEST PROCEDURES. FOR ALL DRAWING REQUESTS, PLEASE CONTACT THE BUYER BY EMAIL. \ 1. SCOPE 1.1 PRE-AWARD / POST AWARD REQUIREMENTS: Due to the critical use of this item and its quality history, a pre-award survey and post-award conference may be required for all new manufacturers. For all previous sources, a post-award conference may be recommended. 1.2 Container shell material is ;ALUMINUM; . 1.3 When discrepancies exist between these requirements and those on current manufacturer's drawings,contact code ;N241.12; or code N241.10 1.4 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;Container Research Corporation; drawing number ( ;05259; ) ;761E001; , Revision ;latest; and all details and specifications referenced therein. 1.5 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification. 1.6 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C. 2. APPLICABLE DOCUMENTS DRAWING DATA=DL761E001 |05259| | |C| | | | DOCUMENT REF DATA=MIL-I-45208 | | |A |810724|A| 1| | 3. REQUIREMENTS 3.1 One third (1/3) unit of desiccant (MIL-D-3464, Type II nondusting) per cubic foot of container interior volume shall be placed in desiccant holder of each container at time of shipment. 3.2 Reference to Cadmium plating shall be deleted and the following substituted: "Finish shall be electrodeposited alkaline Zinc-Nickel Alloy in accordance with ASTM B 841 Class 1, Type B, Grade 3." 3.3 The shock mount listed in the drawing package (whether identified as sole source, recommended, or suggested) has been tested and approved for the shock mitigation system of t…

AgencyDEPT OF DEFENSE
NAICS332439
SAM.gov· Posted Jul 2, 2026#SPRPA126RVC13
ContractSmall Business Set Aside - Total2 days left

2d MarDiv CUAS ADFOR Support

Solicitation Number / RFQ Number:M6700126QM011 Subject: Counter-UAS (CUAS) Adversary Force (ADFOR) Support This is a combined synopsis/solicitation for commercial services prepared in accordance with the format in FAR 12.202(b)(1), as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. This procurement is Small Business Set Aside under NAICS 541990 code size standard of $19,500,000.00. A Quoter’s submission of a quote does not constitute a contract or authorize work to begin. This document is not legally binding and does not commit the US Government in any way. This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2026-01 and Defense Federal Acquisition Regulations Supplement Publication Notice (DPN) 20251110 . In accordance with FAR 12.001(a), when a policy in another part is inconsistent with FAR Part 12, Part 12 shall take precedence. 52.212-2 Evaluation-Commercial Products and Commercial Services (Nov 2021) Basis for Award: The Government intends to award a contract resulting from this solicitation to the responsible quoter whose quote conforming to the solicitation will be most advantageous to Government, price and other factors considered. The following factors shall be used to evaluate quotes: Price Technical Capability Price Reasonableness : Will be conducted in accordance with FAR 12.204(a). The total quoted price, to include shipping costs, will be used in the price evaluation. A written notice of award or acceptance of a quote, mailed or otherwise furnished to the successful quoter within the time for acceptance specified in the quote, shall result in a binding contract without further action by either party. Before the quoter's specified expiration time, the Government may accept a quote (or part of a quote), whether or not there are negotiations after its receipt, unless a written notice of withdrawal is received before award. See attached Performance Work Statement. ***ONLY OPEN MARKET PRICING WILL BE CONSIDERED*** Addendum to 52.212-1 Instructions to Offerors. The Government reserves the right to make an award solely on initial quotes received. Quoters must submit their response to this RFQ via email to lucas.a.beltran.mil@usmc.mil and david.r.bovee.mil@usmc.mil no later than the posted closing date in this listing. Questions will be accepted via email up to four (4) calendar days after the posting of the RFQ. No phone questions will be accepted. The deadline is necessary to ensure timely award and the Government may, in its sole discretion, choose not to respond to questions received after the deadline. Questions will be reviewed and addressed via an amendment to the solicitation and/or posting of the Questions and Answer(s) (Q&A) document. Quotes must contain all requested line items as the contract award will be made in aggregate. Therefore, any quote received without all line items priced will be considered non-responsive. Quoters are instructed to completely fill out the section (Quoter’s Information) below and return it along with your quote. Quotes should be valid for 90 days unless stated otherwise in the quote.

AgencyDEPT OF DEFENSE
NAICS541990
PlaceCamp Lejeune, NC
SAM.gov· Posted Aug 1, 2026#M6700126
ContractSmall Business Set Aside - Total1 day left

Marine Boatyard Support and Industrial Support Lot II Follow-on MAC-IDIQ

AMENDMENT 0004 is issued on 31 JULY 2026 to extend the RFP closing date/time to 07 AUGUST 2026, 1400 San Diego, CA local time, and to update the Ordering Periods One through Five. Click enclosed link titled PIEE Solicitation Module Link N5523625R0012 below to access the subject amendment. The Southwest Regional Maintenance Center (SWRMC) intends to issue a Request for Proposal (RFP) to accomplish Marine Boatyard Support and Industrial Support Lot II for boats, crafts, lighterage, habitability barges, service crafts, and ancillary support equipment (brows, brow platforms, paint floats, camel separators, and loading ramps) greater than or equal to 15 meters or 50 feet in length that can be transported via roadway by a trailer or must be delivered on its bottom (via waterway) and for boats, craft, lighterage or service craft less than 15 meters or 50 feet in length, that must be delivered on its bottom (via waterway). This requirement also includes work on boats, craft, lighterage, service craft, and ancillary support equipment greater than or equal to 15 meters or 50 feet in length up to 260 feet in length. The offeror(s) shall provide specific modifications, upgrades, service life extensions, and repairs to non-commissioned boats, craft, lighterage/service craft and their associated systems (e.g., hull, mechanical, electrical, and electronic systems; trailers; transporters; deployment systems; slings and hoisting systems; launch and retrieval systems, etc.) and periodic maintenance. The offeror(s) shall also perform repairs, alterations, installation upgrades, conversions, habitability, and dry-docking services including hull repairs and preservation for the U.S. Navy berthing and messing program, barges and structures, and their related systems, equipment, and facilities. The offeror(s) shall accomplish the subject availabilities including the dry-berthing or dry-docking of boats, crafts, lighterage, and habitability barges at contractor?s facilities with a 125-mile radius of 32nd Street, Naval Base San Diego, CA. The offeror(s) is responsible for the use of the latest revision of all references, specifications, and NAVSEA Standard Items. The successful offeror(s) will be required to provide all labor, equipment, materials, and facilities in accordance with the specification package. The acquisition and solicitation-to-award process shall abide by Federal Acquisition Regulation (FAR), Defense Federal Acquisition Regulation Supplement (DFARS) and the Navy Marine Corps Acquisition Regulation Supplement (NMCARS) guidelines. The Government anticipates awarding this effort as a supply contract whereas the supply equates to the procurement of repaired, mission-ready boats, crafts, barges, or ancillary support equipment which shall be returned to service with the Fleet. Award will be based on a best-value procurement utilizing past performance, technical, and price as evaluation factors. FAR 52.216-27 Single or Multiple Awards (OCT 1995) applies. This procurement is not restricted to Master Ship Repair Agreement (MSRA) or Agreement for Boat Repair (ABR) contractors. This is a follow-on procurement. All responsible sources may submit a proposal which shall be considered by this agency. The successful offeror will be required to have a SWRMC approved Quality System (IAW NAVSEA Standard Item 009-04), approved and in place at the time of contract award. Offerors shall be registered in the Solicitation Module in Procurement Integrated Enterprise Environment (PIEE) and System for Award Management (SAM) in order to be eligible for award. The RFP is a Total Small Business Set-Aside. The result will be a multiple award indefinite delivery/ indefinite quantity (IDIQ) 5-year contract, including five (5) each 12-month ordering periods. The applicable NAICS code is 336611- Ship Building and Repairing (a small business must have 1,300 or less employees).

AgencyDEPT OF DEFENSE
NAICS336611
SAM.gov· Posted Jul 31, 2026#N5523625R0012
Contract3 days left

Ultrasonic Spray System

SECTION A U.S. Government ~ Tax Exempt Solicitation Information All quotes/responses shall be submitted via email to JaNae Lester at janae.a.lester.civ@us.navy.mil no later than Wednesday, August 5, 2026 @ 4:00 PM EST. Solicitation N0042126Q1305 is issued as an intent to sole source. The Government intends to purchase on a firm fixed-price basis, and to solicit and negotiate the proposed purchase order on a sole source basis with Spraying Systems Co for ultra sonic spray system , under the authority implemented by Federal Acquisition Regulation (FAR) by FAR Part 13.106-1(b). This is a firm fixed-price procurement; therefore, the offeror’s intial offer should represent the vendor’s best quote in terms of price and technical acceptability. ***Basis for Award*** The Government intends to award this on a sole source basis. All interested parties MUST submit their capabilities and a quote no later than Wednesday, August 5th, 2026 @ 4:00 PM EST. The Government will make a decision to consider other offers. ***Instructions to Offerors*** Please include the following information with your response: FOB: Shipping Cost: Cage Code: Small Business – Yes ___ No __ Estimated Delivery Date: If available on a Pricelist please provide a copy. Government Point of Contact: JaNae Lester Naval Air Warfare Center AD (PAX) 21983 Bundy Road, BLDG 441 Patuxent River, MD 20670-1127 Email: janae.a.lester.civ@us.navy.mil

AgencyDEPT OF DEFENSE
NAICS333912
Place0, MD
SAM.gov· Posted Jul 30, 2026#N0042126Q1305
ContractSmall Business Set Aside - Total2 days left

Amendment 0001Rental of Two (2) Nitrogen Trailer {PNSV)

*****PLEASE NOTE**** Combined Synopsis N3904026Q5068A0001 Replaces Combined Synopsis N3904026Q5068 Requirement Title: Requirement Title: Portsmouth Naval Shipyard (PNSY) is seeking to rent a temporary high-pressure nitrogen gas tube trailer. The Statement of Work (SOW) outlines the specifications that meet the essential requirements for the procurement of rental equipment necessary to perform High-Pressure Nitrogen Flasks Charging Operations. The application for this equipment is located at Portsmouth Naval Shipyard in Kittery, ME. Solicitation Number: N3904026Q5068 A001 Response Deadline: August 04, 2026, at 12:30 PM ET POC: Bob Watters, robert.n.watters.civ@us.navy.mil Required Delivery Date/Period of Performance: Base year: 9/4/2026 - 9/2/2027 Option Year 1: 9/3/2027 - 8/31/2028 Option year 2: 9/1/2028 - 8/30/2029 Option year 3: 8/31/2029 - 2/28/2030 Place of Performance: Portsmouth Naval Shipyard Kittery, ME PNSY METHOD OF PROPOSAL SUBMISSION: Offers shall be emailed. All responsible sources may submit a quote which shall be considered by the agency. System for Award Management (SAM): Vendors must be registered in the SAM database to be considered for award. Registration is free and can be completed on-line at http://www.sam.gov/. All quotes shall include the embedded Request for Quote (RFQ). All quotes must have the highlighted sections completed. Please make sure to include all technical data sheets and information relating to the rental equipment.

AgencyDEPT OF DEFENSE
NAICS336611
PlaceME
SAM.gov· Posted Jul 29, 2026#N3904026Q5068A001
Contract2 days left

VALVE,BUTTERFLY

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| INSPECTION AND ACCEPTANCE - SHORT VERSION|8|X||X|||||| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|INVOICE AND RECEIVING REPORT (COMBO)||TBD|SPRMM1|TBD|TBD|TBD|TBD|||TBD|||||TBD| MANDATORY USE OF WORKFLOW PRO (WFP) MOD ASSIST MODULE|1|| NOTICE OF CYBERSECURITY MATURITY MODEL CERTIFICATION LEVEL REQUIREMENTS (NOV 2025))|1|| SECURITY PROHIBITIONS AND EXCLUSIONS (CLASS DEVIATION 2026-O0025)(FEB 2026)|7|||||||| SMALL BUSINESS PROGRAM REPRESENTATIONS (DEV 2026-O0037)(FEB 2026)|20|332919|750||||||||||||||||||| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0043)(FEB 2026))|13|X|X|X|||X|||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||X| 1. All contractual documents (i.e. contracts, purchase orders, task orders, Delivery orders, and modifications) related to the instant procurement are considered to be "issued" by the government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. 2. Drawings or technical data are not available for this item. 3. Delivery days_________aro. 4. Offer valid for _____ days. 5. When submitting quotes via Electronic Data Interchange (EDI), make sure you specify any exceptions (i.e. Mil specs/standards, packaging, Inspection & Acceptance (I&A), packaging houses etc) or follow up with a hardcopy of the exceptions. If nothing is indicated or received, award will be based upon solicitation requirements. Changes or requests for changes after award will have consideration costs deducted on modifications. 6. If you are not the manufacturer of the material you are offering, you MUST state who the Original Equipment Manufacturer (OEM) is �Commercial and Government Entity Code (CAGE) code� and the part number you are offering. 7. Please provide an email address for follow up communications. ____________________________________________________________ 8. It is recommended that vendors provide contact information to NAVSUP Weapon System Support (WSS) Mechanicsburg in order to receive automated notifications from Navy Electronic Commerce Online (NECO) when contracts/modifications are issued by Defense Logistics Agency (DLA) Weapons Support Mechanicsburg and posted on Procurement Integrated Enterprise Environment (PIEE) Electronic Data Access (EDA). To receive these notifications, contact: NAVSUPWSS code 025, procurement systems design and contract support division Via email at NAVSUPWSSITIMPHelpdesk@navy.mil. Please include the following information with your request: CAGE code, company name, address and Point-of-Contact (POC) with phone number and email address. 9. Contractors can view their orders, contracts and modifications at the EDA web tool. This web tool is located at the PIEE website. It is recommended that the contractor register for EDA at https://piee.eb.mil/. Click on new user and registration. Any order resulting from this Request for Quotation will require electronic submittal of Invoice and Receiving Report (COMBO) through PIEE-WAWF. 10. The following DLA Procurement Notes are applicable to this requirement: E06 Inspection and Acceptance at Source (JUN 2018) 11. INSPECTION OF MATERIAL WILL BE AT (CAGE & ADDRESS): ______________________________________________________________ INSPECTION OF PACKAGING AND FINAL ACCEPTANCE OF MATERIAL WILL BE AT (CAGE & ADDRESS): ______________________________________________________________ 12. UCF SECTION F PRODUCTION FACILITY CHANGES (a) The performance of any of the work contracted for in any place other than that named in the contract is prohibited unless specifically approved by the Contracting Officer. Written requests for …

AgencyDEPT OF DEFENSE
NAICS332919
SAM.gov· Posted Jul 28, 2026#SPRMM126QMH19